Pond Pump Troubleshooting
Eighty percent of pump problems can be fixed in minutes, saving you further inconvenience.
The pump can be called the "heart" of the pond. Without it, the relaxing, rushing sound of the water over the
rocks would not exist. The fish and the filtering bacteria in the biological filter also depend on the pump to
provide fresh, oxygenated water.
Most quality pumps should get you at least three years of maintenance-free service of re-circulating the water
in your pond, so how can the pump not be working? Odds are the pump is actually fine. As a pond owner, there
are a few things you can do to help detect, and hopefully fix, the problem before you call the installer or return
the pump to the merchant from which you purchased it. Eighty percent of pump problems can be fixed in
minutes, saving you further inconvenience. The following troubleshooting steps will help you quickly identify,
and hopefully solve, the problem with a failed pump.
Proceed with the following actions until the problem is found.
A problem with your pond’s pump doesn’t always mean the pump is ready to be replaced. It doesn’t mean you
have to wait for warranty repairs or for your landscape contractor to pay you a visit. Familiarizing yourself with a
few simple technicalities will help you fix the problem yourself and your pump could be running normally in no
time at all.
taken directly from www.aquascapedesigns.com
Eighty percent of pump problems can be fixed in minutes, saving you further inconvenience.
The pump can be called the "heart" of the pond. Without it, the relaxing, rushing sound of the water over the
rocks would not exist. The fish and the filtering bacteria in the biological filter also depend on the pump to
provide fresh, oxygenated water.
Most quality pumps should get you at least three years of maintenance-free service of re-circulating the water
in your pond, so how can the pump not be working? Odds are the pump is actually fine. As a pond owner, there
are a few things you can do to help detect, and hopefully fix, the problem before you call the installer or return
the pump to the merchant from which you purchased it. Eighty percent of pump problems can be fixed in
minutes, saving you further inconvenience. The following troubleshooting steps will help you quickly identify,
and hopefully solve, the problem with a failed pump.
Proceed with the following actions until the problem is found.
- First of all, is the pump receiving water? This sounds like an obvious question, but it’s not an uncommon
problem. Water evaporates and, if not replaced, the lack of it can affect the operation of the pump. In this
situation, the pump may actually be running, but just not receiving enough water. A lot of times you can
actually hear the "hum" or "gurgle" of the pump when this is happening. - Make sure nothing is blocking the flow of water to the pump. Large boulders, debris blocking the front of
the skimmer opening, a clogged skimmer net, or clogged skimmer filter can reduce the flow of water. If
you have a skimmer, make sure the water level is 3/4" below the top of the skimmer opening. If the
established water level is lower than this, the pump may suck the skimmer dry, causing the thermal shut-
off to activate. The thermal shut-off will deactivate once the pump cools back down.The proper water
level will then need to be established. - The pond is too small for the stream above it. The lowest pond must be large enough to supply enough
water to start the circulation of the stream and/or waterfall. Once the pump is started, it may be
necessary to add a few inches of water to the lower pond in order to account for the water used to feed
the stream, pipe, and waterfalls. Lower ponds that are designed too small may not be able to supply
enough water to start the streams/waterfalls. This will cause the water in the pond to drop below the
opening of the skimmer upon the initial start-up, and starve the pump of water. - The pump may be vapor-locked.This term sounds complicated, but it simply means that air is trapped
inside the pump. Pumps are designed to push water, not air so when an air bubble gets trapped, the
pump becomes vapor locked.When this happens, the impeller is spinning, but water is not being pushed.
Listen to see if you hear the hum of the pump. A vapor-lock can be fixed by tilting the pump, allowing the
air bubble to escape from the intake. - Is the electrical supply operating properly? Premature pump failures can occur due to a faulty electrical
supply. For example, using an extension cord, especially one over 25-feet long, may cause irregular
power to the pump. This can cause performance problems with the pump, and possibly reduce its
lifespan. Check to make sure all electrical connections are functioning properly. Verify that a certified
electrician installed and tested the electrical while the pump was running. Oftentimes, GFCI circuits are
set too sensitive, causing them to repeatedly trip the breaker. - Check the electric box to see if the ground fault circuit interrupter (GFCI) has tripped. The proper
electrical setup for the pond should include a GFCI outlet. A GFCI is a safety device installed to protect
people from receiving a shock in the event of an electrical malfunction and will shut the power down if it
senses a problem. GFCIs are very sensitive and can sometimes trip during a thunderstorm or a power
surge. It is also very common for outside outlets to be electrically connected to other rooms within the
house, such as the bathroom. Many times, the combination of the pump running on the pond and
someone using devices like a blow dryer in the bathroom can overload the GFCI and trip the breaker.
Ask your electrician to make sure the electrical outlet for the pond is dedicated to just the pond. - Unplug the pump and disconnect the union fitting found at the top of the pump connection.The water will
back-flush from the biological filter back into the skimmer. This will help flush out any debris that is
clogged along the length of the pipe.
- (Reference above images - click on image for larger view) Pull the pump out of the skimmer and inspect
the intake on the pump for any lodged debris. Some pumps are capable of handling solids and debris up
to about 5/8". On some occasions, debris may become lodged in the housing of the pump. This could
stop the impeller from turning, restricting the flow of water, and eventually causing the pump to stop
operating properly. Thoroughly check the pump intake, including the area above the impeller where
small debris, such as gravel, may be trapped. Plug in the pump after inspecting it for debris, and see if
the impeller spins.
- The impeller may fail to spin when the pump has been out of operation for a period of time (such as over
the winter). Try to assist it by using a screwdriver or similar tool to give it a little kick-start.When the
pump begins to operate, let it run for 5 to 10 seconds. Unplug the pump, wait a few seconds, and plug it
back in. The impeller should begin to spin without assistance this time. - If you still have no luck, bring the pump over to another electrical outlet, specifically one that contains a
GFCI breaker, and see if the pump operates. This will tell you if the pond’s electrical supply is bad, or if
there is something internally wrong with the pump. If the pump trips the GFCI, then it is likely that there is
something wrong with the pump, and it should be replaced. If the pump runs without a problem on the
second outlet, you’ll want to have a qualified electrician come out and check the pond’s electrical setup
A problem with your pond’s pump doesn’t always mean the pump is ready to be replaced. It doesn’t mean you
have to wait for warranty repairs or for your landscape contractor to pay you a visit. Familiarizing yourself with a
few simple technicalities will help you fix the problem yourself and your pump could be running normally in no
time at all.
taken directly from www.aquascapedesigns.com
